Catalog Search
|
Errata
Project #0212, Deck Chair, 6/15/2002:
The illustration shows the curved seat slats in both the "major anatomy" drawing and "chair assembly" drawing with the curved part forward. They should be reversed so the curved part is to the rear.
Project #710, Gazebo, 5/15/2002:
The people who used to make the (optional) copper finial on the top of the Gazebo have retired and sold the business to:
Coppersmiths
39399 John West Road
Oakhurst, CA 93644
Phone:(559)658-8909
Project #9901, Kitchen Island, 6/21/2002:
The phone number with the info you need for Allied Plywood is 800-759-6631.....(not the number printer in plans for #9901).
Project #1201, Garage Workshop, 1/3/2003:
The parts list refers to Tandem No-Profile Full Extension Fully Concealed Slides, Rockler part number of #30971. The part number should be #30871.
Project #0001, Garage Workshop, 1/3/2003:
The parts list refers to Tandem No-Profile Full Extension Fully Concealed Slides, Rockler part number of #30971. The part number should be #30871.
Project #0313, Wall Mounted Tool Chest, 2/25/03:
Addional materials information:
| Nominal Dimensions | Quantity/Length | Approximate Dimensions | Part of Project | | 3/8” Mahogany Plywood | 1 pc. 4 ft. X 8 ft. | Crosscut at 72”, rip 1 pc. 17 1/8” and 1 pc. 13 11/16”. Cut 17 1/8” wide pc. into 2 pcs. 35 1/4” long, and 13 11/16” wide pc. into 2 pcs. 31 7/8” long. | Panels for door boxes and door panels. |
Project #0105, Garden Armchair, 5/16/03:
We discovered that the back leg measurements did not print on the measured drawing. On the back leg, the measurement from the top of the back leg to the mortise is 2" and the mortise height is 2 3/4".
Project #0307, Media Press, 7/10/03:
The plan for the Media Press specifies a quantity of 2 drawer pulls. However, 6 pulls are need, one each for the small drawers, two each for the large drawers.
Project #0307, Media Press, 11/16/03:
The cutting schedule calls for the sides of the lower chest to be 22 3/8" inches wide. On the plan showing the rabbits, it calls for the sides to be 23 3/8" inches wide. The larger, 23 3/8" measurement, is correct.
Project #706, Lutyens Bench, 8/7/03:
The distance between the mortise for the seat slat and the mortise for the back seat support as well as the end seat support is 2 3/4".
Project #1213, Breakfront Cabinet, 11/6/03:
Nominal Dimensions | Quantity/Length | Approximate Dimensions | Part of Project | 3/4” Birch Plywood | 1 Pc. 2 Ft. X 4 Ft. | Rip 6 pcs. 3” wide. Cut one pc. 47 1/4” long. Cut one 48” pc. into 2 pcs. 12 1/2” long and 1 pc. 18 1/4” long. Cut one 48” pc. iinto 2 pcs. 13” long and 2 pcs. 7 1/2” long. Cut two 48” pcs. into 4 pcs. 23 1/4” long. Cut one 48” pc. into 4 pcs. 10 1/2” long. | Pcs. for top frame of lower cabinet and drawer support frames |
Project #0013, Breakfront Cabinet, 11/6/03:
Nominal Dimensions | Quantity/Length | Approximate Dimensions | Part of Project | 3/4” Birch Plywood | 1 Pc. 2 Ft. X 4 Ft. | Rip 6 pcs. 3” wide. Cut one pc. 47 1/4” long. Cut one 48” pc. into 2 pcs. 12 1/2” long and 1 pc. 18 1/4” long. Cut one 48” pc. iinto 2 pcs. 13” long and 2 pcs. 7 1/2” long. Cut two 48” pcs. into 4 pcs. 23 1/4” long. Cut one 48” pc. into 4 pcs. 10 1/2” long. | Pcs. for top frame of lower cabinet and drawer support frames |
Project #507, Sideboard, 12/8/03:
The upper front rail drawing is incorrect. The notch for the center legs should be on the other side of the groove that receives the corner blocks and drawer guides.
Project #1209, Outdoor Patio Table, 12/8/03:
A typo: the grooves in the crosspieces for the top should be 5/16" wide x 1/2" deep.
Project #0009, Outdoor Patio Table, 12/8/03:
A typo: the grooves in the crosspieces for the top should be 5/16" wide x 1/2" deep.
Project #0107, Outdoor Cupboard, 1/20/04:
The plans call for 30 peices of paneling, but 32 are needed.
Project #0301, Deluxe Router Station, 1/20/04:
The materials list instructs the builder to cut the 16x16 inch plexiglass to 16 7/8" square. But it should be cut to 15 5/8" square.
Project #1211, Sharpening Station, 2/6/04:
The cutting diagram for the 2 step side peices has a typo: it states to cut one to 3 5/8" X 18" and the other one to 3 3/8" X 18". Both should be cut to 3 5/8" X 18"
Project #0011, Sharpening Station, 2/6/04:
The cutting diagram for the 2 step side peices has a typo: it states to cut one to 3 5/8" X 18" and the other one to 3 3/8" X 18". Both should be cut to 3 5/8" X 18"
Project #0204, Adirondack Loveseat, 3/3/04:
The Major Anatomy drawing shows the incorrect measurement for the front legs. The length of the front legs measure 23 1/4 inches as stated in the Materials List.
Project #0110, Mailbox, 3/3/04:
The measurements shown for the brace and mortises are incorrect as shown in the Base Trim and Mortises for Brace detailed drawing. The measurements for the thickness of the brace, the width of the mortise in the post and the width of the mortise in the bottom of the mailbox should all read 2 3/4 inches, not 2 7/8.
Project #0110, Mailbox, 3/3/04:
The second piece of 2 x 8 redwood should be ripped to 5 3/4 inches wide instead of 5 1/2 inches as noted in the Material list.
Project #603, Toy Chest, 3/3/04:
In the Material List, the length of hinge called for is 48 inches, but it should be 42 inches as shown in the Major anatomy.
Project #606, Marble Roll, 3/31/04:
The direction of the top angled dado on the left side should be up, not down as indicated in the detailed drawing for the Sides.
Project #0508, Tilt Top Table, 12/4/06:
The materials list calls for 10/4 X 6 Cherry. The correct measurement is 10/4 X 10.
Project #0603, Workshop Helpers, 12/4/06:
For the mobile tool stand, the material for the top is missing from the Material List. We used 3/4 inch MDF but you could use any grade of 3/4 inch plywood.
Project #0810, Adirondack Trio, 12/30/08:
The distance from the front of the Angled leg pattern to the location of the back edge of the lower rear crosspiece should be 19 15/16 in. The length of the Arm is correct but the grid is short by one square. Extending the grid by one square where the sides are parallel will correct the pattern.
|
|
|
